110mm Niagara Ogee Gutter 90dg Angle - External

Specifications

Application Type: Rainwater Gutter
Profile Type: 110mm Niagara Ogee
Product Type: Gutter Angle - External
Angle of Bend: 90-degrees
Brand: FloPlast
Width: 173mm 
Depth: 96mm
Length: 176mm
Material: PVCu
Standards: Manufactured to BS EN 607
                      Kitemarked - KM501316

This 110mm Niagara Ogee 90-degree external gutter angle is designed to create a tight change in direction around an external corner (decorative front bends away from you).  It forms part of a Niagara Ogee guttering system that provides a cost-effective solution for new builds, refurbishments, conservatories, and extensions in areas of heavy rainfall. Easy to install with good flow capacity and a 10-year performance and colour guarantee.

This is for an external bend in a Niagara Ogee gutter run only. For an internal bend, choose the Niagara Ogee 90dg Angle - Internal product instead.

Product Features at a Glance:

• An ornate (K-Style) profile.
• Clip system for fast & easy installation.
• Changes the direction of a gutter externally through 90 degrees.
• FloPlast 10 year colour and performance guarantee
• Covered by BSI Kitemark – no. KM501316.
• Manufactured to BS EN 607 standards.

Manufacturer’s Advice: Fascia brackets should be installed at a maximum of 1m apart along each gutter length and within 150mm of any other joint or fitting. FloPlast recommend the use of lubricant on all gutter seals for ease of fitting and improved performance.

FloPlast Niagara Ogee Guttering System

FloPlast is a well-established manufacturer and supplier of Plastic Building and Plumbing systems to the UK construction sector. They specialise in Roofline products with an extensive range of Rainwater systems, including the Niagara Ogee gutter.

Features & benefits

• A traditional ogee style profile.
• One of the highest capacity PVC-U domestic rainwater systems on the market.
• Revolutionary designed moulded water-tight seal and retaining clip pre-fitted for fast user-friendly installation.
• Suitable for all properties old and new.
• Outlet connects to Square or Round downpipes.
• Internal/external angles and right/left hand stopends available.
• Running outlet designed to cope with above average rainfall.
• Fits 65mm Square, 68mm Round, 80mm Downpipe.
• System is covered by a BSI Kitemark – no. KM501316.

Gutter Flow Rates

With a max flow rate of 2.61 litres/sec for a gutter system installed with a 1:350 fall ratio (2.16 l/s if installed level), the Niagara Ogee gutter system, connected to a 65mm Square downpipe via a stopend outlet, is suitable for a maximum roof area of 125m2 (104m2 if installed level). If connected to an 80mm Round downpipe, the maximum roof area increases to 138m2 (114m2 if installed level).

With a max flow rate of 4.77 litres/sec for a gutter system installed with a 1:350 fall ratio (4.05 l/s if installed level), the Niagara Ogee gutter system, connected to a 65mm Square downpipe via a running outlet at the centre of the gutter run, is suitable for a maximum roof area of 229m2 (194m2 if installed level). If connected to an 80mm Round downpipe via a running outlet, the maximum roof area increases to 251m2 (213m2 if installed level).

System Standards
FloPlast’s Niagara Ogee guttering products are designed and manufactured to the following standards:

• BSI Kitemark number: KM 501316 – BS EN 607, BS EN 12200 and BS EN 1462 Plastic rainwater, piping and guttering systems for above ground use – Unplasticized poly vinyl chloride (PVC-U.
• BS EN 607 – Eaves gutters and fittings made of PVC-U.
• BS EN 1462 – Brackets for eaves gutters.
• BS EN 12200-1 – Plastics rainwater piping systems for above ground external use. Unplasticized poly (vinyl chloride) (PVC-U).
• BS EN 681 – Elastomeric seals. Material requirements for pipe joint seals used in water and drainage applications. Thermoplastic elastomers.

Please Note: All images shown are used for illustration purposes only and may differ from the actual product supplied.