115mm Hi-Cap Gutter External Stopend

Specifications

Application Type: Rainwater Gutter
Profile Type: Hi-Cap (Deep)
Product Type: Gutter Stopend - External
Brand: FloPlast
Width: 136mm 
Depth: 94mm
Length: 53mm
Material: PVCu
Standards: Manufactured to BS EN 607
                      Kitemarked - KM501316

This Hi-Cap external stopend is designed to cap-off the open ends of gutter lengths. It forms part of a 115mm Hi-Cap, high capacity guttering system that provides a cost-effective solution for new builds, refurbishments, conservatories, and extensions. Easy to install with good flow capacity and a 10-year performance and colour guarantee.

Important Note: to cap-off Hi-Cap gutter unions, angles, or outlets, use Internal Stopends instead of External Stopends.

Product Features at a Glance:

• A semi-elliptical (Deep) profile.
• Clip system for fast & easy installation.
• Cap-off Hi-Cap gutter lengths.
• Available in multiple colour options.
• FloPlast 10-year colour and performance guarantee
• Covered by BSI Kitemark – no. KM501316.
• Manufactured to BS EN 607 standards.

Manufacturer’s Advice: Fascia brackets should be installed at a maximum of 1m apart along each gutter length and within 150mm of any other joint or fitting.  For optimum performance of Hi-Cap gutter systems, we recommend the use of either a FloPlast 68mm or 80mm round downpipe system. FloPlast recommend the use of lubricant on all gutter seals for ease of fitting and improved performance.
 

FloPlast Hi-Cap Guttering System

FloPlast is a well-established manufacturer and supplier of Plastic Building and Plumbing systems to the UK construction sector. They specialise in Roofline products with an extensive range of Rainwater systems, including the Hi-Cap gutter.

Features & benefits

• A semi-elliptical profile.
• High capacity-ideal for large roof areas.
• Pre-fitted gutter seal retaining clip system for fast user-friendly installation.
• High flow rate means less outlets and less drainage runs.
• Both 68mm & 80mm round downpipes can be connected to the gutter system.
• System is covered by a BSI Kitemark – no. KM501316.

Gutter Flow Rates

With a max flow rate of 2.30 litres/sec for a gutter system installed with a 1:350 fall ratio (1.84 l/s if installed level), the Hi-Cap gutter system, connected to a 68mm Round downpipe via a stopend outlet, is suitable for a maximum roof area of 111m2 (88m2 if installed level). If connected to an 80mm Round downpipe, the maximum roof area increases to 121m2 (97m2 if installed level).

With a max flow rate of 4.05 litres/sec for a gutter system installed with a 1:350 fall ratio (3.42 l/s if installed level), the Hi-Cap gutter system, connected to a 68mm Round downpipe via a running outlet at the centre of the gutter run, is suitable for a maximum roof area of 216m2 (164m2 if installed level). If connected to an 80mm Round downpipe via a running outlet, the maximum roof area increases to 238m2 (180m2 if installed level).

System Standards
FloPlast’s Half Round guttering products are designed and manufactured to the following standards:

• BSI Kitemark number: KM 501316 – BS EN 607, BS EN 12200 and BS EN 1462 Plastic rainwater, piping and guttering systems for above ground use – Unplasticized poly vinyl chloride (PVC-U.
• BS EN 607 – Eaves gutters and fittings made of PVC-U.
• BS EN 1462 – Brackets for eaves gutters.
• BS EN 12200-1 – Plastics rainwater piping systems for above ground external use. Unplasticized poly (vinyl chloride) (PVC-U).
• BS EN 681 – Elastomeric seals. Material requirements for pipe joint seals used in water and drainage applications. Thermoplastic elastomers.

Please Note: All images shown are used for illustration purposes only and may differ from the actual product supplied.